Bonnell Used Equipment

ONLY TWO PLOWS LEFT! Serial numbers 5120 through 5126, 7 reconditioned moldboards with new Bonnell Metropolitan style push tables. The moldboards are 10 foot long by 36 in. high with built-in integral shield with optional rubber snow flap already added. Pin on swivel bar is 30-1/2 in. on center with ears. Carbon steel cutting edge that is 5/8 in. thick x 6 in. high x 10 foot long. Standard chain lift already installed. Hydraulic cushion valve installed on the plow to protect the reversing cylinders from damage when an obstruction is hit. The plow comes with 36” plow markers and are painted CAT Yellow.

Knapheide flatbed, sand blasted and repainted chassis, Buyers under body toolbox, Knapheide flatbed has a $3000 value. Air conditioning, power steering, power brakes, cruise control, tilt steering wheel, vinyl seats grey, towing hitch with 6 prong plug-in, tires have about 50% tread left and tire size is 225/70R19.5.
188,300 miles
Standard cab dual wheel rear axle

2007 FORD F350 SD XL SUPER CAB, DRW, 126,000 MILES, V-10 TRITON GAS ENGINE, AUTO TRANS, WHITE EXT, VINYL GREY INTERIOR, VINYL FLOOR, A/C, CRUISE CONTROL, CD RADIO, TIRES IN EXCELLENT CONDITION (90%) LT245/75 R17, SERVICE BODY, (VIN:1FDWX36Y67EB35206)

CALL JOE AT (815) 509-8457 OR (815) 284-3819

FSE,1/2X8X10' CARBON AASHO TOP PUNCH 1-1/2 GA.
SQUARE HOLE FOR 5/8 CARRIAGE BOLTS

R191-DD-8436-Z
9" DIRECT DRIVE REPLACEMENT TAILGATE SPREADER. IT IS GALVANIZED WITH FRESH ORANGE PAINT INCLUDES MOUNTING KIT, SPREADER IN EXCELLENT CONDITION.

V SPINNER ASSEMBLY, BOTTOM HALF ONLY
18 INCH STEEL SPINNER DISC
HYDRAULIC MOTOR TOP MOUNT

Used Valk Low-Profile hitch frame only, with rigid lift arm and 3x10 single acting lift cylinder. Penn-Dot style hook-up, welded in place.

HTC QUICK SANDER
BELT CONVEYOR/BI-DIRECTIN
WHITE
SAND BAGGER BI-DIRECTIONAL
2 SAND BAG ATTACHMENTS MOUNTING KIT INLCUDED
TAIL LIGHTS ROUND
SHUT OFF VALVE IN ATTACHMENTS REMOTE RELAY
ELECTRIC SHUT OFF VALVE AT MOTORS

BONNELL 9' TAPER (FULL ROLL)
9' CUTTING EDGE
MEYER STYLE TABLE DESIGN
2X12 CYLINDERS
CHAIN LIFT ASSY

Used Western Suburbanite mount kit #1223, fits Ford 1997 - 2003 F150

1997 ELGIN GEO VAC

NOTE: AUXILARY ENGINE TO OPERATE SWEEPER HAS FAILED. UNIT SOLD AS/IS – PRICED AS/IS

9' BALDERSON V-PLOW, DON'T GET CONFUSED ON THE SIZE OF THIS PLOW. THE FARTHEST POINT ON EACH WING STANDS OUT TO 91/2'. THIS ISN'T MEANT FOR A SKID STEER OR OTHER SMALLER TRACTOR.

Used Flink QL2 quick link assembly, truck portion, pin on style. Pin on holes 3" center to center, fits Bonnell hitches.

Swenson 10' v-box spreader with top screens. Very poor condition. needs new floor, bearings and shaft.

Swenson Stainless Steel PV spinner assembly, for hydraulic drive units. Short Verson. Bonnell #BV2-002307ss, Swenson #00002 296 04

USED, SNOW PLOW, FLINK MODEL 375 ONE WAY, TRIP EDGE WITH SHOES, RUBBER DEFLECTOR AND MONROE QUICK HITCH, BROWN PAINT IN FAIR CONDITION, THE PLOW ITSELF IS IN EXCELLENT CONDITION NO CRACKS OR BENDS GOOD SET OF CAST 1 WAY SHOES, GOOD SET OF CUTTING EDGES

USED, SPREADER, TAILGATE, MONROE MS-966 6" AUGER W/STD SPINNER

USED, BONNELL TAPER MOLDBOARD 12 FOOT PC TABLE DESIGN

Used 11 Foot straight plow, pc table design. Rough. As is.

USED, MEYER MODEL E-47 HYDRAULIC UNIT, REFURBISHED,

6" Direct Drive tailgate spreader auger. 2" shorter than standard auger. Will fit Bonnell/Swenson tailgate spreader with a little tweaking.

ONE PAIR OF MONROE TRIP BARS FOR TORSION TRIP PLOW, VERY GOOD CONDITION.

USED 10' SNOW DEFLECTORS, 3/8" X 12" RUBBER BELTING. USED, AS IS. PRICE IS EACH.

10'X 16" LEAF VAC HOSE, USED

SOME WIRE SHOWING

CAB SHIELD WHITE
14" RISE, 84" WIDE
12" OVERHANG

CAB SHIELD, PRIMED ONLY

28" RISE, 90" WIDE

29" OVERHANG

USED V-PLOW, AS IS.

USED, WOOD MODEL CADET 84 3 PT SINGLE SPINDLE 7' MOWER

11' Bonnell tapered plow. Good condition

12' VIKING SNOW PLOW WITH WHEEL LOADER HITCH ATTACHMENT. PLOW IS IN GREAT CONDITION.

TORSION TRIP EDGE 11' BONNELL SNOW PLOW. CHAIN AND SADDLE LIFT WITH A PC TABLE AND A STANDARD 2 PIN HOOK UP. PLOW IS IN GREAT CONDITION.

NEW, MEYER #17098 EASY MOUNT CLASSIC KIT COMPLETE. FITS 1992 TO 1998 FORD F-250 4WD 4600 FGAWR , OLD INVENTORY (2 AVAILABLE)

USED, BONNELL U19-DD SPREADER S/N 2131

UNIT HAS BEEN REPAIRED, BLASTED, PRIMED AND REPAINTED ORANGE. HAS NEW GALVANIZED SPINNER ASSY AND MOUNTING HARDWARE INCLUDED. NEW AUGER MOTOR AND 4 BOLT BEARING HAS BEEN INSTALLED

ALITEC 16" ASPHALT GRINDER. MODEL# CP16BH AND THE SERIAL# 3028R0892

USED, SNOW PLOW, MONROE 11' X 48" POWER REVERSIBLE SNOW PLOW, ORANGE.

USED TAILGATE REPLACEMENT SPREADER, MODEL# ER69-CD-C. ALL ELECTRIC, WITH CONTROLS AND WIRING.

NEW, TAKE OFF BOX, 2008 CHEVY 8' BED, WITH THE TAIL LIGHTS AND THEY ARE ALL RED WITH A WHITE BACK UP LIGHT AND TAILGATE, PAINTED RED

NEW, 2008 CHROME BUMPER, CHEVY. NEVER BEEN USED BUT HAS BEEN SITTING AROUND....STILL LOOKS BRAND NEW

USED, HINIKER #25011815HITCH, FITS 2002-2008 DODGE 1500
NEW HINIKER PRICE $601.00

***There are 2 of these drags available***

MAKE: 572 ROAD DRAG

MODEL: 572-HRLS

S/N:

SPECIAL NOTES:EVERYTHING NEW ON DRAG BESIDES MAIN WELDMENTS
-NEW BLADES
-NEW HYDRAULIC CLYINDERS
-NEW HOSES
-NEW TIRES
-NEW HARDWARE
-COMPLETELY BLASTED, PRIMED AND PAINTED ORANGE
-NEW DECALS

NEW UNIT $27,500.00

BONNELL 572 PERFECT ROAD MAINTAINER
COMPLETE ROAD DRAG WITH OPTIONAL HRLS
HYDRAULIC RAISE LOWER AND SWING OF REAR BLADE
OVERALL 29' LONG X 10' WIDE CUTTING WIDTH
5/8" X 8" CARBON CUTTING EDGES STANDARD
(2) 11L X 15" 8-PLY TIRES
(3) SINGLE ACTING HYDRAULIC CYLINDERS FOR FRONT AND REAR RAISE AND LOWER
(2) DOUBLE ACTING CYLINDERS FOR RAISE AND LOWER OF TAIL SECTION
(1) DOUBLE ACTING CYLINDER FOR SWING OF TAIL SECTION
PAINTED BONNELL ORANGE

MODEL #572 HRLS

HTC CONVEYOR SPREADER 1200 SERIES. THE BELT IS 12" WIDE. THE PAINT IS IN ROUGH CONDITION.

Crysteel dump body and hoist. Came off of a tandem axle dump truck. This body and hoist has been slightly used. It has all the lights with the back-up alarm and wiring still attached to the body along with the hoist and it's sub frame. It is an air lock tailgate and that is all hooked up also.
The body is 168" long x 96" wide x 40" tall.

USED, SPREADER, WARREN ALUMINUM V-BOX SPREADER.

-122" long x 82" wide x 55" tall
-MODEL# E/AC-2420AL-10
-SERIAL# SC14412

RATED CAPACITY 6.3 YD

Bonnell under tailgate salt spreader. It is in very good condition and comes with a spinner kit. The paint is in really good condition, but the poly spinner is dry rotted and cracked. May be needing a new poly spinner.

CHEVY SILVERADO CHROME BUMBER

BOLTS UP TO A 2009-2013 TRUCK. THE BUMPER IS IN GREAT CONDITION

CHEVY SILVERADO CHROME BUMBER

BOLTS UP TO A 2009-2013 TRUCK. THE BUMPER IS IN GREAT CONDITION

CHEVY SILVERADO CHROME BUMBER

BOLTS UP TO A 2009-2013 TRUCK. THE BUMPER IS IN GREAT CONDITION

CHEVY SILVERADO CHROME BUMBER

BOLTS UP TO A 2009-2013 TRUCK. THE BUMPER IS IN GREAT CONDITION

FORD F-150 GREEN TAILGATE

LOOKS LIKE IT FITS A 2004-2008, HAS SOME SCRATCHES ON THE OUTSIDE OF THE TAILGATE

CHEVY TAILGATE, GREEN

CONDITION IS GREAT BUT HAS THE NORMAL WEAR THAT A USED TAILGATE WOULD HAVE FROM SLIDING THINGS IN AND OUT OF THE TRUCK BED.

CHEVY TAILGATE, GREEN

CONDITION IS GREAT BUT HAS THE NORMAL WEAR THAT A USED TAILGATE WOULD HAVE FROM SLIDING THINGS IN AND OUT OF THE TRUCK BED.

CHEVY TAILGATE, GREEN

CONDITION IS GREAT BUT HAS THE NORMAL WEAR THAT A USED TAILGATE WOULD HAVE FROM SLIDING THINGS IN AND OUT OF THE TRUCK BED.

CHEVY TAILGATE, GREEN

CONDITION IS GREAT BUT HAS THE NORMAL WEAR THAT A USED TAILGATE WOULD HAVE FROM SLIDING THINGS IN AND OUT OF THE TRUCK BED.

USED WESTERN #62330 UNIMOUNT KIT. THIS MOUNT IS IN REALLY GOOD SHAPE FOR BEING USED. WE GOT A NEW BOLD KIT AND A FEW NEW BRACKETS TO MAKE THE MOUNT KIT COMPLETE. COMES WITH A 12V SOLENOID
Solenoid #(684-1221-012)

USED, BONNELL SNOW PLOW MODEL 123762M5E
-JD YELLOW
-10 SPRINGS
-FRONT FLAP
-HEAVY DUTY EVEN WEAR SHOES
-EXTENDED TABLE
-SWIVEL BAR
-CHAIN LIFT

USED, SWIVEL BAR/QA LOOP

USED, MONROE MC-6000/QAS/UQH RECEIVER

$1837.00 NEW

2012 CHEVROLET 2500 REAR BUMPER. HAS 7 PRONG TRAILER PLUG ATTACHMENT.

2012 CHEVROLET 2500 SILVER TAILGATE. I'M NOT SURE EXACTLY WHAT YEAR TRUCKS THIS WILL FIT SO YOU MAY HAVE TO DO SOME RESEARCH.

This spreader is designed to mount on the rear of a truck dump body, below the tailgate, supported by brackets bolted to the side rails of the dump body. Support spreader and other heavy components solidly when positioning on truck dump body. On occasion the vertical end plates of the spreader may be bent slightly in or out, check these for squareness and realign if necessary, before installation.

Mounting:

Position and level spreader under the dump body tailgate with the montor to the inside of the truck, and with the rubber seal strip on forward side of spreader as close as possible to the dump body floor.

with the spreader in the desired position, attach Conveyor mounting brackets (0011077100) to the spreader with clevis pins, flat-washers and hairpin keepers. Next, position conveyor mounting brackets against the side rails of the dump body and drill (3) 1/2" diameter holes through the the mounting brackets and side rail, secure with 1/2" diameter holes through both the mounting brackets and side rails, secure with 1/2" Grade 5 bolts and flange nuts. Repeat for opposite side.

That is just an idea of what installation would be. This Conveyor spreader is in great shape you can go to Swenson Products website to get the manual for the STCC conveyor spreader. Swenson stopped making these in 2004 so you need to look and the Archive Manuals under Documents.

• Crank adjustable moldboard
swing and gauge wheels

• Quick attach and detach

• 5/8" x 8" Hi Carbon steel
cutting edge, standard Highway
punching

• Swivel and float features

• One double acting lift
cylinder included

• Custom mounting brackets

The Windrow Eliminator will strike off the windrow left
behind the motor grader eliminating the need for a second pass. The finish grade is set by the parallel lift hitch
and the pneumatic wheels. Specify a Bonnell Windrow
Eliminator and you will never chase another windrow.

FSE,1/2X6X9' CARBON AASHO TOP PUNCH 1-1/2 GA WITH SQUARE HOLE.

FSE,1/2''X8''X5' CARBON AASHO TOP PUNCH 1-1/2 GA.

CDB, HEAT TREATED, SERRATTED L.H. ANGLE 5/8"X8"X72"

Bonnell R161-DD-8422-Z Replacement tailgate spreader. 6" auger, agitator, direct drive, 84" wide x 22" tall, galvanized, with spinner and mount kit.

Did you know that Bonnell Industries offers a plow refurbishment program? Bring in your used snow plow of any brand, and we will sand blast and repaint it to a color of your choice! We can also perform any repairs that need to be done at that time too, including damaged, cracked, or rusted moldboards, worn frogs, hoses, etc.

Pictures above are before and after of actual plow.

Price below includes sand blasting and repainting only - Yellow, Orange, or Black. Other colors and repairs extra. Freight not included. Blasting of powder coat plows to bare steel may be extra.

HT90SS (USED IN MT MODELS) 25 SERIES, LEXAN/STEEL

CONTROL BOX STAND

SUB-FRAME KIT F-150/250LD 97 LINCOLN

STANDARD SUB-FRAME KIT CHEV/GMC

ADAPTER KIT

SNOWSPORT HD BLADE 84 INCH LONG X 18 INCH TALL, ALUMINUM BLADE WITH RUBBER CUTTING EDGE, END PEICES ARE RUBBER WITH STEEL RETAINERS, BLADE GUIDES AND HARWARE KIT. ASSEMBLY REQUIRED.

SNOWSPORT, PLOW MOUNT, 2007-2010 CHEV/GMC NEW BODY 1500. PRICE INCLUDED WITH SNOW SPORT BLADE.

SNOWSPORT, PLOW MOUNT
2009-2010 DODGE RAM 1500 4WD
PRICE INCLUDED WITH SNOW SPORT BLADE.

SNOWSPORT ATV ALL TERRAIN BLADE, 72 INCH LONG X 14.5 INCH TALL, ALUMINUM BLADE WITH RUBBER CUTTING EDGE AND HARWARE KIT. ASSEMBLY REQUIRED.

SUGGESTED BLADE SIZE: UTV ALL MODELS = 72 INCH BLADE